# Beam Deflection Calculator

URL: https://speedycalculator.com/calculators/construction/beam-deflection/
Last updated: 2026-10-25

> The beam deflection calculator finds the maximum deflection, bending moment and shear of simply supported and cantilever beams under a point load or a uniformly distributed load, from the span, modulus of elasticity and moment of inertia.

## Inputs

- Beam and load
- Span (m, ft, cm, in, yd)
- Point load (N, kN, lbf, kip, kgf)
- Uniform load (kN/m, N/m, lbf/ft, lbf/in)
- Material
- Custom modulus of elasticity (GPa, MPa, ksi, psi)
- Moment of inertia (cm⁴, mm⁴, in⁴, m⁴)

## Results

- Maximum deflection
- Maximum bending moment
- Maximum shear
- Span ÷ deflection (L/δ)

## Formula

```
Simply supported, centre point load: δ = PL³ ÷ 48EI, M = PL ÷ 4
Simply supported, UDL: δ = 5wL⁴ ÷ 384EI, M = wL² ÷ 8
Cantilever, end load: δ = PL³ ÷ 3EI, M = PL
Cantilever, UDL: δ = wL⁴ ÷ 8EI, M = wL² ÷ 2
```

## Explanation

Beams must be strong enough not to break and stiff enough not to sag visibly or crack finishes. Building codes limit live-load deflection to L/360 for floors and L/240 for roofs, so the span divided by the deflection should be at least that number. Deflection depends on the load, the span (to the third or fourth power), the material stiffness E and the cross-section's moment of inertia I.

### How to use the Beam Deflection Calculator

- **Beam and load**
- **Span**
- **Point load**
- **Uniform load**
- **Material**
- **Custom modulus of elasticity**
- **Moment of inertia**
- Every result field is editable: type into **Maximum deflection** and **Moment of inertia** plus every other field update to match.

Results update as you type, and every field accepts the units shown in its menu.

### How it works

Choose the support and load case, enter the span, the load, the material (or E) and the moment of inertia of the section. Type a target deflection to find the moment of inertia you need.

### Tips for an accurate estimate

- Keep units consistent – the calculator handles conversions, but check every field's unit before reading a result.
- Use values from standards, data sheets or test pieces whenever you have them; typical values are only a starting point.
- Apply appropriate safety factors and have structural, electrical and pressure work checked by a qualified professional.
- Record the inputs you used so the calculation can be reviewed later.

### Common mistakes to avoid

- Confusing diameter and radius, or nominal and actual sizes.
- Using allowable stresses and ultimate strengths interchangeably.
- Treating rule-of-thumb results as a substitute for code tables or an engineered design.

### Inputs explained

FieldWhat to enterBeam and loadChoose one: Simply supported – point load at centre, Simply supported – uniform load, Cantilever – point load at free end, Cantilever – uniform loadSpanUnits: m, ft, cm, in, ydPoint loadUnits: N, kN, lbf, kip, kgfUniform loadUnits: kN/m, N/m, lbf/ft, lbf/inMaterialChoose one: Structural steel (200 GPa), Aluminium (69 GPa), Softwood timber (11 GPa), Hardwood timber (13 GPa) …Custom modulus of elasticityUnits: GPa, MPa, ksi, psiMoment of inertiaUnits: cm⁴, mm⁴, in⁴, m⁴

### Example values

How the main result changes when **Moment of inertia** changes and everything else stays at the example values above:

Moment of inertia (cm⁴)Maximum deflection (mm)4,1781.9956,2671.338,3560.99710,4450.79812,5340.66516,7120.499

## Worked example

Inputs — Beam and load: Simply supported – uniform load; Span: 4 m; Point load: 10,000 N; Uniform load: 5 kN/m; Material: Structural steel (200 GPa); Custom modulus of elasticity: 10 GPa; Moment of inertia: 8,356 cm⁴.

Results — **Maximum deflection = 0.997 mm**; Maximum bending moment = 10,000 N·m; Maximum shear = 10,000 N; Span ÷ deflection (L/δ) = 4,011.

## Key terms

- **E**: Young's modulus, the stiffness of the material.
- **I**: Second moment of area of the cross-section.

## FAQ

**What is an acceptable beam deflection?**
Typically L/360 for floors under live load, L/240 for roofs and L/180 for cantilevers – check your code.

**What is the moment of inertia?**
A property of the cross-section shape (I = b h³/12 for a rectangle) that measures resistance to bending; steel tables list it for every section.

**Why does doubling the span matter so much?**
Deflection grows with L³ for point loads and L⁴ for distributed loads – doubling the span makes a uniformly loaded beam sag 16 times as much.

**What formula does the Beam Deflection Calculator use?**
Simply supported, centre point load: δ = PL³ ÷ 48EI, M = PL ÷ 4.


## Sources

- [AISC Steel Construction Manual – Beam diagrams and formulas](https://www.aisc.org/)